Intelligent Touch Manager DCM601A71

This Installation Manual is for Intelligent Touch Manager

MODELS: DCM601A71
 

CONTENTS:

  • 1Before Installation … page 7
  • 1.1 Checking that all accessories are
    included … page 7
  • 1.2 Understanding external dimensions
    … page 8
  • 1.3 Understanding where terminals and switches
    are located … page 10
  • 1.3.1 Rear face … page 10
  • 1.3.2 Front panel … page 11
  • 1.3.3 Side face … page 12
  • 1.3.4 Routing of cables … page 12
  • 1.4 Determining installation place … page 13
  • 1.4.1 Installation place and mounting
    direction … page 13
  • 1.4.2 Environmental conditions … page 13
  • 1.4.3 Required space … page 13
  • 2 Connection … page 14
  • 2.1 Removing terminal cover from rear
    face … page 14
  • 2.2 Connecting DIII-NET-compatible air conditioning
    equipment … page 14
  • 2.2.1 Terminals location and conceptual connection
    diagram … page 15
  • 2.2.2 Requirements that must be met … page 16
  • 2.2.3 Precautions for using multiple centralized
    controllers … page 16
  • 2.3 Connecting a LAN cable … page 17
  • 2.3.1 Terminals location and conceptual
    connection diagram … page 18
  • 2.3.2 Requirements that must be met … page 18
  • 2.4 Connecting I/O module … page 19
  • 2.4.1 Terminals location and conceptual
    connection diagram … page 19
  • 2.4.2 Requirements that must be met … page 19
  • 2.4.3 Address setup … page 20
  • 2.5 Connecting an emergency stop input device
    or electric energy meters … page 20
  • 2.5.1 Terminals location and conceptual
    connection diagram … page 21
  • 2.5.2 Requirements that must be met … page 21
  • 2.6 Connecting iTM plus adaptors … page 22
  • 2.6.1 Terminals location and conceptual
    connection diagram … page 22
  • 2.6.2 Requirements that must be met … page 23
  • 2.7 Connecting power supply … page 23
  • 2.7.1 Terminals location and conceptual
    connection diagram … page 23
  • 2.7.2 Requirements that must be met … page 24
  • 3 Installation … page 25
  • 3.1 Wall mounting … page 25
  • 3.1.1 Parts to be used … page 25
  • 3.1.2 Installation procedure … page 25
  • 3.2 Flush wall mounting … page 26
  • 3.2.1 Parts to be used … page 26
  • 3.2.2 Wall opening dimensions … page 27
  • 3.2.3 Installation procedure … page 27
  • 3.3 Direct mounting to control enclosure
    … page 30
  • 3.3.1 Parts to be used … page 30
  • 3.3.2 Wall opening dimensions … page 30
  • 3.3.3 Installation procedure … page 30
  • 4 Basic Setup … page 32
  • 4.1 Powering on data backup battery … page 32
  • 4.2 Powering on intelligent Touch Manager
    and air conditioners … page 32
  • 4.3 Setting up display language … page 33
  • 4.4 Setting up locale … page 33
  • 4.5 Setting time zone … page 34
  • 4.6 Setting current time and daylight
    saving time … page 34
  • 4.7 Confirming air conditioner auto
    registration results … page 35
  • 4.8 Assigning a DIII-NET address for each air
    conditioner … page 35
  • 4.8.1 Remote controller buttons and
    areas … page 35
  • 4.8.2 Procedure for a wired remote
    controller … page 36
  • 4.8.3 Procedure for a navigation remote
    controller … page 38
  • 4.8.4 Setting an unique address to each unit
    (when power distribution is enabled) … page 40
  • 5 Outdoor Unit Address Setup … page 41
  • 5.1 Procedure … page 41
  • 6 Quick Operation Guide … page 42
  • 6.1 Viewing target area and management point
    information in list format … page 42
  • 6.2 Viewing target areas and management
    points …page 42
  • 6.3 Starting/stopping an area or management
    point … page 43